Visual Productions forum

Author Topic: CLS Jade B Colour flow  (Read 121 times)

August 07, 2019, 05:08:55 AM
Read 121 times

linusbergman

  • Member
  • *
  • Posts: 4
Hi there,

Would it be possible for you to provide a Cuety personality for the CLS Jade B Colour Flow (see attached)?

Thank you in advance!

August 07, 2019, 07:51:11 AM
Reply #1

Julien Levaufre

  • Global Moderator
  • Member
  • *****
  • Posts: 2089
    • www.visualproductions.nl
well, i read the manual of your profile, and for sure it's not a commun fixture!
Over 15 DMX channels only one can be patch to a standard fader "Dimmer", all others are unusual parameters that should go on customs faders...
Sadly cuety only provide 2 custom faders, so I am a little bite stuck!
The best would be for you to tell me which channel you need on which parameter and I will create a custom file for it.
Julien Levaufre
Visual Productions BV

August 07, 2019, 08:38:38 AM
Reply #2

linusbergman

  • Member
  • *
  • Posts: 4
Hi Julien,

Thanks for the quick reply. I was trying some of the generic profiles but they didnt' work the way I expected, hence my request.

The lights are being used in a control room setting, so I don't need anything fancy...basically being able to control color temperature and to dim the lights.

Hope the above helps (as I am by no means a light person).

Thanks for your assistance.
Linus

August 08, 2019, 02:44:11 AM
Reply #3

Julien Levaufre

  • Global Moderator
  • Member
  • *****
  • Posts: 2089
    • www.visualproductions.nl
I think I  understood how those lights are working but to be able to provide you the right file can you telle me which model you are using: RGBQ, RGBW, AWB etc...
Julien Levaufre
Visual Productions BV

August 08, 2019, 09:29:49 AM
Reply #4

linusbergman

  • Member
  • *
  • Posts: 4
Hi again,

It should be the RGBW model. Attached is a photo of the type plate.

Thanks again for your assistance.

August 08, 2019, 06:39:53 PM
Reply #5

Julien Levaufre

  • Global Moderator
  • Member
  • *****
  • Posts: 2089
    • www.visualproductions.nl
PLease find included your fixture file.
Tell me if it's working fine or not because I am really not sure how this fixture works.
enjoy ;)
« Last Edit: August 15, 2019, 10:26:04 AM by Julien Levaufre »
Julien Levaufre
Visual Productions BV

August 15, 2019, 09:21:11 AM
Reply #6

linusbergman

  • Member
  • *
  • Posts: 4
Hi Julien,

Thanks. Tried the supplied file but unfortunately it did not work - in fact hardly anything happened when moving the sliders.

I don't know if the following will help at all, but when using the Generic RGBW profile, adjusting the sliders one by one give the following results:


      0---------------127---------------255
R:   Wh -----> Cy   | Wh -----> Cy    | Wh
G:   Wh -----> Ma | Wh -----> Ma    | Wh
B:   Wh -----> Yl   | Wh -----> Yl      | Wh

W:   Wh -----> Bl   | Wh -----> Bl      | Wh

i.e. it cycles through complimentary colors twice within the 0-255 range if that makes sense?

August 15, 2019, 10:28:44 AM
Reply #7

Julien Levaufre

  • Global Moderator
  • Member
  • *****
  • Posts: 2089
    • www.visualproductions.nl
Ok so it's seems I really did not understand how this fixture is working...and I think it will stay a mystery.
The best would be to be able to test all the channels because on the manual it seems they are 14!
Anyway, from the new informations you gave me i've created a new fixture file (with your pseudo) that you can find in the file I updated on my previous post.
I hope this will be better and I don't I will really be able to do anything better.
Note that i cannot say to cuety to stop the value 127... one fader will always go from 0 to 255.
Julien Levaufre
Visual Productions BV