Visual Productions forum

Author Topic: URGENT file request Showtec Kanjo Spot 60  (Read 2454 times)

December 05, 2016, 10:41:51 AM
Read 2454 times

RaffelNL

  • Member
  • *
  • Posts: 7
Hi,
Awaiting a new movinghead to be added to a project.
Uploaded the manual including the dmx chart,
 could you please suply a fixture file for Cuety?

Thnx in advance,

Ralph
« Last Edit: December 06, 2016, 08:40:50 AM by RaffelNL »

December 05, 2016, 10:45:27 AM
Reply #1

RaffelNL

  • Member
  • *
  • Posts: 7
Hi,

Could you please suply a fixturefile, for Cuety,
Gear: Showtec Ignitor 6 strobo

Attached the manual of the fixture,

Thnx in advance,

Ralph
« Last Edit: December 06, 2016, 08:41:10 AM by RaffelNL »

December 05, 2016, 11:08:54 AM
Reply #2

RaffelNL

  • Member
  • *
  • Posts: 7
Hi,

Would like to have a fixture file for the Showtec 51340 laser,
it's a 24 ch fixture, is that a problem?

See the attached manual for the DMX chart

many thanks in advance,

Ralph
« Last Edit: December 06, 2016, 08:41:25 AM by RaffelNL »

December 07, 2016, 02:33:13 PM
Reply #3

Julien Levaufre

  • Administrator
  • Member
  • *****
  • Posts: 3234
    • www.visualproductions.nl
Sorry for delay but creating a laser fixture for cuety is not really easy...
So please find your fixture file inclued, as lot's of functions of the laser were not present in cuety i put some on the RGBW faders, i hoppe it will be ok for you.
And tricky thing i'did, as cuety do not manage subfixtures and your laser can create 2 paterns ( so kind of subfixtures) i divided the laser in 2 fixtures ( mode patern 1 +mode patern 2 so to use completely your laser you need to patch those 2 modes together at the same dmx address.
ANd to activate the dmx control you need to use the first custom fader.
I hoppe everything is clear for you,,
Enjoy, ;).
Julien Levaufre
Visual Productions BV

December 08, 2016, 10:46:39 AM
Reply #4

RaffelNL

  • Member
  • *
  • Posts: 7
Hi Julien,

Thanks for the support!

December 13, 2016, 09:20:57 AM
Reply #5

RaffelNL

  • Member
  • *
  • Posts: 7
Julien,

What name did you give the file for the laser?

...Same question for the ignitor 6

Thanks in advance for your reply!

December 13, 2016, 12:00:27 PM
Reply #6

Julien Levaufre

  • Administrator
  • Member
  • *****
  • Posts: 3234
    • www.visualproductions.nl
teh name for the laser is galactic rgb 720 and for the strobe it's ignitor 6..
Please note that when you use customs fixtures from the user.personality file you need to use the manufactuer from the top of the list with [user] before.
In your case you should have at the top of the manufacturer list [user]showtec, your fixtures are in this folder.
Julien Levaufre
Visual Productions BV

December 14, 2016, 12:38:09 PM
Reply #7

RaffelNL

  • Member
  • *
  • Posts: 7
There is no Ignitor 6 in the [Showtec] library that shows op on top, found the laser en the Kanjo60, Ignitor 6 doesn't show.
searched the entire list, can't find it.
Could you please check?

December 14, 2016, 02:00:54 PM
Reply #8

Julien Levaufre

  • Administrator
  • Member
  • *****
  • Posts: 3234
    • www.visualproductions.nl
Yes you were right, i don't know what it was not included, so please find the new fixture file... sorry about that.
Please note that you will be able to see only the 3ch mode.
ENjoy,
Julien Levaufre
Visual Productions BV

 

SMF spam blocked by CleanTalk